All purchases made on this website are secured by Thawte.
Designed for heavy duty anchoring into solid concrete. The concrete wedge anchor is available in zinc plated steel, stainless
steel and hot-dipped galvanized. . Wedge anchors come in diameters 1/4”, 5/16”, 3/8”, 1/2”, 5/8”, 3/4”, 7/8”,
1”, and 1-1/4” and many different lengths depending on the thickness of the material to be attached to the concrete. Anchor diameter is equal
to the hole size. |
For medium duty fastening/anchoring to concrete, brick or block base material. Concrete sleeve anchors are available in zinc
plated and stainless steel. Sleeve anchors are available in six diameters in the hex nut 1/4”, 5/16”, 3/8”, 1/2”, 5/8”and
3/4”. The 1/4 ”, 5/16” and 3/8” also come in a flat countersunk head. The 1/4”diameter is also available in a round head”.
The anchor diameter equals the hole diameter. |
Tapcon brand concrete screws are ideal for fastening to concrete, brick or block base material. Tapcons are available in standard Stalgard coating or
as stainless steel concrete screws. Tapcon concrete screws come in two head styles, hex washer, and flat phillips.and two diameters 3/16” and 1/4".
The 3/16” tapcon uses a 5/32” bit and the 1/4” tapcon uses a 3/16” bit. |
| PRICES & SIZES |
PRICES & SIZES |
PRICES & SIZES |
Designed for use in solid concrete base material. Drop-in anchors are a female type anchor with inside diameters of 1/4", 3/8”,
1/2”, 5/8” and 3/4" with national coarse threads. The drop-in anchor requires a setting tool for expanding the anchor.
Drop-in anchors are available in zinc plated or stainless steel. |
An excellent medium duty anchor for attaching to concrete, brick or block base material. The design of the machine screw anchor allows
it to fit into irregular holds. The machine screw anchor is described by the size of the internal threads, 1/4”, 3/8”, 1/2”,
5/8” and 3/4”. The internal threads of the machine screw anchors allow temporary fastening and rebolting with out affecting
the holding values. The machine screw anchor is set using a setting tool. |
Designed for use in concrete, brick or block. Leadwood screw anchors are for light duty fastening and easy to install. Using the corresponding
sheet metal screw #6, #8, # 10, #12 or #16 to expand the leadwood screw anchor in the base material. The leadwood screw anchor/shield
is made from a rust resistant zamac material. |
| PRICES & SIZES |
PRICES & SIZES |
PRICES & SIZES |
Designed for attaching to concrete, brick or block base material. The Single expansion anchor/shield bolt can be removed and replaced
without affecting the holding values of the single expansion anchor. Single expansion anchors come in six sizes that refers to the inside
diameter of the anchor, i.e. size of the bolt to be used 1/4”, 5/16”, 3/8”, 1/2”, 5/8” and 3/4”, Refer
to chart for the size of hole to be drilled for each anchor. |
Excellent holding values in concrete, brick, stone and block. The Double expansion anchor/shield can be removed and replaced without
affecting the holding values of the double expansion anchor. Double expansion anchors come in six sizes that refers to the inside diameter
of the anchor, i.e. size of the bolt to be used 1/4”, 5/16”, 3/8”, 1/2”, 5/8” and 3/4”, Refer to chart
for the size of hole to be drilled for each anchor. |
Designed for fastening to concrete, brick and block. The standard lag type screw is used to expand the concrete lag shield anchor.
The lag shield anchor comes in five diameters 1/4”, 5/16”, 3/8”, 1/2”, 5/8” and 3/4”, which refers
to the internal threads or the diameter of the lag screw. Lag shields come in two different lengths for each size, short or long version. |
| PRICES & SIZES |
PRICES & SIZES |
PRICES & SIZES |
Ideal for light duty fastening into concrete, brick or block base material. Nylon nail-it anchors are not recommended for structural
or overhead applications. Nylon nail-it anchors come in two diameters 3/16” and 1/4”and three different head styles, mushroom,
round and flat. |
Excellent for fastening to concrete, brick or block. The design of the concrete metal hit anchor once installed makes the anchor tamper-resistant.
Concrete metal hit anchors come in two diameters 3/16” and 1/4” and a variety of lengths from 7/8” to 3”. The
anchor diameter equals the hole diameter. |
Designed to be used in solid concrete base material as a light duty fastener. Once installed the concrete split drive anchor is tamper-resistant.
Two head styles are available in the split drive anchor, round head or flat countersunk. The split drive anchor comes in one diameter
of 1/4” and lengths from 1-1/2” to 4”. The hole size that needs to be drilled is 1/4”. |
| PRICES & SIZES |
PRICES & SIZES |
PRICES & SIZES |
Concrete strike anchors are medium to heavy-duty anchors for use in solid concrete base material. The hole that needs to be drilled
in the concrete is equal to the diameter. The concrete strike anchor can be visually inspected, when the center pin is flush with the
top of the anchor the strike anchor is set properly. The strike anchor comes in 1/4”, 5/16”, 3/8”, 1/2”, 5/8”,
and 3/4” diameters and a variety of lengths, determined by the thickness of the material to be fastened. |
Used in drywall. The unique design of the wall driller anchor allows for simple and fast installation without pre-drilling a hole. They
are available in two different materials, nylon or a metal Zamak material. and two different sizes for use with a #6 or #8 sheet metal
screw. |
Designed for use in hollow base material such as drywall or hollow concrete blocks. Toggler bolts are available in 3/16”, 1/4”,
3/8” and 1/2” diameters and the diameters refer to the diameter of the bolt that fits into the toggler bolt. |
| PRICES & SIZES |
PRICES & SIZES |
PRICES & SIZES |
Toggler hollow wall anchors are versatile for fastening into thin paneling, gypsum board, plasterboard masonite and many other hollow
base material. The Toggler comes in three different sizes that are based on the grip range. The TA is for 1/8” to 1/4”, TB
is for 3/8” to 1/2” and TC is for 5/8” to 1/2”. |
Provide a non-protruding and high-strength connection for anchoring hurricane shutters. The hurricane shutter insert anchor system introduces
a new anchoring concept designed to anchor to concrete or block. |
|
| PRICES & SIZES |
PRICES & SIZES |
|
