Hilti
1/2" x 7" Hilti Kwik Bolt 3 HDG Hot-Dip Galvanzied, 25/Box
- SKU:
- WAG127;H
- MPN:
- 378086
- Availability:
- Ships in 1-3 days!
Description
- GALVANIZED: Helps prevent rusting in moist environments; lower maintenance
- AVAILABLE IN DIAMETERS FROM 3/8" TO 1-1/4": Ensures proper diameter for any application; versatile
- EXCEPTIONAL PERFORMANCE: Consistent holding values provides peace of mind
- STAINLESS STEEL CLIP: Ensures long life
- STAMPED WITH LENGTH I.D.: Provides easy inspection
Applications
The anchor is made from Carbon Steel, and is hot-dip galvanized. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.
Environment
The anchor is designed for use in a moist environment.
Hole Diameter/Bit Diameter
The anchor requires a 1/2" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.
Diameter of Anchor
The diameter of the anchor is 1/2".
Length Anchor
The length of the anchor is 7"
Thread Type
The threads on the anchor are national coarse threads that measures 1/2" with 13 threads per inch, commonly referred to as 1/2"-13.
Thread Length
The length of the threads on the anchor is 4-3/4" in length.
Packaging
The anchor is packaged with 25 pieces per box and is packaged with the correct number and diameter of nuts and washers.
Depth of Hole
The depth of the hole that is required for the anchor should be a minimum of 1/2" deeper than the anchor will penetrate the concrete. This will allow space for dust created during the installation process to fall, which will prevent the anchor from bottoming out in the hole before full penetration into the concrete.
Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 1/2" diameter anchor requires the hole in the fixture to be {MinimumFixtureHoleDiameter(InPlace)}.
Wrench Size
The size of the wrench required to turn the nut to set the anchor is 3/4".
Torque Value
To be set properly in the concrete, the anchor must be torqued to between 40 ft./lbs.
Markings
The anchor is stamped with the letter L on the threaded end to allow inspection of the anchor after installation. The letter "L" designates an overall length of the anchor as between 7" up to, but not including 7-1/2" in length.
Bit Size | 1/2" |
Minimum Embedment | See PDF |
Thread Length | 4-3/4" |
Primary | Concrete only |
Environment | Moist |
Thread Type | 1/2" - 13 |
Type | Male |
Diameter | 1/2" |
Length | 7" |
Material | Carbon Steel Hot-Dip Galvanized |
Box Qty | 25 |
Minimum Spacing | See PDF |
Minimum Edge Distance | See PDF |
Maximum Fixture Thickness | See PDF |
Minimum Fixture Hole Diameter (In Place) | 9/16" |
Minimum Fixture Hole Diameter (Hole Spotted) | 1/2" |
Length ID Code | L |
Maximum Torque | 40 ft./lbs. |
Wrench Size For Nut | 3/4" |
Length Measurement | End to End |
Brand Name | Hilti |
Additional Information
Bit Size: |
1/2" |
Minimum Embedment: |
See PDF |
Thread Length: |
4-3/4" |
Primary: |
Concrete only |
Environment: |
Moist |
Thread Type: |
1/2" - 13 |
Type: |
Male |
Diameter: |
1/2" |
Length: |
7" |
Material: |
HDG Hot-Dip Galvanized |
Box Qty: |
25 |
Minimum Spacing: |
See PDF |
Minimum Edge Distance: |
See PDF |
Minimum Fixture Hole Diameter (In Place): |
9/16" |
Minimum Fixture Hole Diameter (Hole Spotted): |
1/2" |
Length ID Code: |
L |
Maximum Torque: |
40 ft./lbs. |
Wrench Size For Nut: |
3/4" |
Length Measurement: |
End to End |
Brand Name: |
Hilti |