Hilti
3/4" x 10" Hilti Kwik Bolt 3 SS 304, 10/Box
- SKU:
- WAS3410;H
- MPN:
- 286028
- Availability:
- Ships in 1-3 days!
Description
- MADE FROM 304 STAINLESS STEEL: Can be used in wet, submerged environments and will not rust; lowered maintenance costs
- COMPLETE LINE: All sizes means the right fastener for every job; wide range of purchase choices
- PACKAGED WITH CORRECT NUMBER AND SIZE OF NUTS & WASHERS: Comes complete and ready to install; saves time and money
- SPECIAL CLIP DESIGN: Prevents anchor from spinning during installation, assures a successful installation process
- CHAMFERED THREADED END: Helps prevent thread damage during installation
Applications
The anchor is made from 304 Stainless Steel. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.
Environment
The anchor is designed for use in a wet environment.
Hole Diameter/Bit Diameter
The anchor requires a 3/4" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.
Diameter of Anchor
The diameter of the anchor is 3/4".
Length Anchor
The length of the anchor is 10"
Thread Type
The threads on the anchor are national coarse threads that measures 3/4" with 10 threads per inch, commonly referred to as 3/4"-10.
Thread Length
The length of the threads on the anchor is 5-7/8" in length.
Packaging
The anchor is packaged with 10 pieces per box and is packaged with the correct number and diameter of nuts and washers.
Depth of Hole
The depth of the hole that is required for the anchor should be a minimum of 1/2" deeper than the anchor will penetrate the concrete. This will allow space for dust created during the installation process to fall, which will prevent the anchor from bottoming out in the hole before full penetration into the concrete.
Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 3/4" diameter anchor requires the hole in the fixture to be {MinimumFixtureHoleDiameter(InPlace)}.
Wrench Size
The size of the wrench required to turn the nut to set the anchor is 1-1/8".
Torque Value
To be set properly in the concrete, the anchor must be torqued to between 110 ft./lbs.
Markings
The anchor is stamped with the letter R on the threaded end to allow inspection of the anchor after installation. The letter "R" designates an overall length of the anchor as between 10" up to, but not including 11" in length.
Bit Size | 3/4" |
Minimum Embedment | See PDF |
Thread Length | 5-7/8" |
Primary | Concrete only |
Environment | Wet |
Thread Type | 3/4" - 10 |
Type | Male |
Diameter | 3/4" |
Length | 10" |
Material | 304 Stainless Steel |
Box Qty | 10 |
Minimum Spacing | See PDF |
Minimum Edge Distance | See PDF |
Maximum Fixture Thickness | See PDF |
Minimum Fixture Hole Diameter (In Place) | 13/16" |
Minimum Fixture Hole Diameter (Hole Spotted) | 3/4" |
Length ID Code | R |
Maximum Torque | 110 ft./lbs. |
Wrench Size For Nut | 1-1/8" |
Length Measurement | End to End |
Brand Name | Hilti |
Additional Information
Bit Size: |
3/4" |
Minimum Embedment: |
See PDF |
Thread Length: |
5-7/8" |
Primary: |
Concrete only |
Environment: |
Wet |
Thread Type: |
3/4" - 10 |
Type: |
Male |
Diameter: |
3/4" |
Length: |
10" |
Material: |
304 Stainless Steel |
Box Qty: |
10 |
Minimum Spacing: |
See PDF |
Minimum Edge Distance: |
See PDF |
Maximum Fixture Thickness: |
See PDF |
Minimum Fixture Hole Diameter (In Place): |
13/16" |
Minimum Fixture Hole Diameter (Hole Spotted): |
3/4" |
Length ID Code: |
R |
Maximum Torque: |
110 ft./lbs. |
Wrench Size For Nut: |
1-1/8" |
Length Measurement: |
End to End |
Brand Name: |
Hilti |