3/8" x 5" Ankr-TITE® Anchor, 50/Box

(No reviews yet) Write a Review
Contact us for information, see page for alternatives.


Frequently bought together:


  • Bolt Size is Hole Size 
  • Available in four combinations
    1. Zinc plated carbon steel with steel clip
    2. Hot-dip galvanized carbon steel with 304 stainless steel clip
    3. All 304 stainless steel
    4. All 316 stainless steel
  • Sets up fast - Needs less rotation to achieve required torque
  • Unique "safety shoulder" - Supports clip when anchor is under strain and minimizes bolt-end collapse and/or clip slippage under ultimate loading conditions
  • Enlarged dimples on clip - Reduce slip and increase response in lighter concrete
  • 360° segment contact on clip equalizes load distribution : Increases load-carrying capacity - More adaptable to"forgiving" in different installation conditions

The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.

The anchor is designed for use in a dry environment.

Hole Diameter/Bit Diameter 
The anchor requires a 3/8" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor  
The diameter of the anchor is 3/8".

Length Anchor  
The length of the anchor is 5"

Thread Type  
The threads on the anchor are national coarse threads that measures 3/8" with 16 threads per inch, commonly referred to as 3/8"-16.

Thread Length 
The length of the threads on the anchor is 3-1/4" in length.

The anchor is packaged with 50 pieces per box and is packaged with the correct number and diameter of nuts and washers.

Minimum Embedment 
The minimum anchor embedment into the concrete is 1-3/4". Therefore, the anchor must be installed so that a minimum of 1-3/4" of the anchor is embedded into the concrete.

Depth of Hole 
The depth of the hole that is required for the anchor should be a minimum of 1/2" deeper than the anchor will penetrate the concrete. This will allow space for dust created during the installation process to fall, which will prevent the anchor from bottoming out in the hole before full penetration into the concrete.

Maximum Fixture Thickness 
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 2-7/8". This will ensure that the minimum embedment of 1-3/4" will be met.

Fixture Hole Diameter 
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 3/8" diameter anchor requires the hole in the fixture to be 7/16".

Wrench Size  
The size of the wrench required to turn the nut to set the anchor is 9/16".

Torque Value 
To be set properly in the concrete, the anchor must be torqued to between 20-25 ft./lbs.

Edge Distance 
It is very important not to install the anchor any closer than 3-1/8" from an unsupported edge of the concrete.

The anchor is stamped with the letter H on the threaded end to allow inspection of the anchor after installation. The letter "H" designates an overall length of the anchor as between 5" up to, but not including 5-1/2" in length.

Products Specifications 
Bit Size 3/8"
Minimum Embedment 1-1/2"
Thread Length 3-3/4"
Primary Concrete only
Environment Dry
Thread Type 3/8" - 16
2000 PSI Concrete - Pull-Out (lbs.) * 1223
2000 PSI Concrete - Shear (lbs.) * 3238
Type Male
Diameter 3/8"
Length 5"
Material Carbon Steel Zinc Plated
Box Qty 50
Minimum Spacing 3-3/4"
Minimum Edge Distance 1-7/8"
Maximum Fixture Thickness 3-1/8"
Minimum Fixture Hole Diameter (In Place) 1/2"
Minimum Fixture Hole Diameter (Hole Spotted) 3/8"
Length ID Code H
Maximum Torque 25 - 30 ft./lbs.
Wrench Size For Nut 9/16"
Length Measurement End to End
Brand Name Wej-It
Product Type Wedge
* Values shown are average ultimate values and are offered only as a guide and are not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe working load
View AllClose

Additional Information

Bit Size:
Minimum Embedment:
Thread Length:
Concrete only
Thread Type:
3/8" - 16
2000 PSI Concrete - Pull-Out (lbs.) *:
2000 PSI Concrete - Shear (lbs.) *:
Carbon Steel Zinc Plated
Box Qty:
Minimum Spacing:
Minimum Edge Distance:
Maximum Fixture Thickness:
Minimum Fixture Hole Diameter (In Place):
Minimum Fixture Hole Diameter (Hole Spotted):
Length ID Code:
Maximum Torque:
25 - 30 ft./lbs.
Wrench Size For Nut:
Length Measurement:
End to End
Brand Name:
View AllClose