ITW/Buildex®

1/4" x 3-3/4" Tapcon Hex Carbon Steel Blue Climaseal® Coated HW4-334, 100/Box

(No reviews yet) Write a Review

SKU:: CSH14334;T
UPC:: 092097951471
MPN:: HW-4334
Availability:: In Stock, Ships Today!

$53.28

Quantity:

Description
Additional Information

Description

Products Features

LOWER INSTALLATION TORQUE: Fast easy installation; saves time
HIGHER HOLDING VALUES: Higher quality installation; optimal holding strength
CLIMASEAL® COATING: Provides long-lasting rust resistance exterior
AMERICAN MADE: A high-quality domestic product

Products specifications

Bit Size	3/16"
Box Qty	100
Minimum Embedment	1"
Head Type	Hex Washer
Thread Type	Threadform Technology™
Minimum Edge Distance	3"
Maximum Fixture Thickness	2-3/4"
Minimum Fixture Hole Diameter (In Place)	5/16"
Minimum Fixture Hole Diameter (Hole Spotted)	5/16"
Brand Name	ITW/Buildex
Driver Size	5/16"
Minimum Spacing	4"
Thread Length	1-3/4"
2000 PSI Concrete - Pull-Out (lbs.) *	750
2000 PSI Concrete - Shear (lbs.) *	900
Length Measurement	Underneath head
Diameter	1/4"
Length	3-3/4"
Material	Carbon Steel Blue Climaseal® Coated
Environment	Dry to Moist
Type	Male

* Values shown are average ultimate values and are offered only as a guide and are not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe working load

Application Video

Installation Video

Installing a 1/4" x 3-3/4" Hex Tapcon® Concrete Screw

Drill a 3/16" hole into the concrete using a carbide-tipped bit that meets ANSI Standards B212.15.
Drill the hole a 1/2" deeper than the anchor will penetrate the concrete, making sure the minimum embedment requirements of 1" is met.
The hole can be drilled while the fixture is in place. The minimum hole in the fixture for the 1/4" x 3-3/4" Hex Tapcon® Concrete Screw is 5/16".
Clean the hole with a wire brush, vacuum, compressed air, or a blow-out bulb.
Insert the point of the 1/4" x 3-3/4" Hex Tapcon® Concrete Screw into the hole. Make sure that the screw being installed will penetrate the base material a minimum of 1" but no deeper than 1-3/4".
Using a 5/16" nut driver hex driver for the anchor , turn the screw clockwise, applying slight pressure until the head of the screw is snug against the material being fastened.
Always use proper personal protective equipment per manufacturer's and OSHA instructions.

Product Video

Application Photos

1/4" x 3-3/4" hex tapcon - block - dock hardware

Downloads

Installation Document

Technical Document

View AllClose

Additional Information

Bit Size:	3/16"
Minimum Embedment:	1"
Thread Length:	1-3/4"
Environment:	Dry to Moist
Material:	Carbon Steel Blue Climaseal® Coated
Thread Type:	Threadform Technology™
2000 PSI Concrete - Pull-Out (lbs.) *:	750
2000 PSI Concrete - Shear (lbs.) *:	900
Type:	Male
Diameter:	1/4"
Length:	3-3/4"
Box Qty:	100
Minimum Spacing:	4"
Minimum Edge Distance:	3"
Maximum Fixture Thickness:	2-3/4"
Minimum Fixture Hole Diameter (In Place):	5/16"
Minimum Fixture Hole Diameter (Hole Spotted):	5/16"
Head Type:	Hex Washer
Length Measurement:	Underneath head
Driver Size:	5/16"
Brand Name:	ITW/Buildex