JavaScript seems to be disabled in your browser.
You must have JavaScript enabled in your browser for full functionality of this website.
 
You have no items in your shopping cart.
Free Shipping
$25 or more
               
 
 

1" x 6" Wedge Anchor Zinc Plated, 5/Box

$26.00 per Box of 5
    Payment types
   Availability: In Stock / Ships Today
  Questions?

SKU: WA16
  MFG: CONFAST®

 

  • Customer Reviews
  • EV MDC SSL
    EV MDC SSL


Products Features
  • ZINC ​PLATED: Helps ​prevent ​rust ​in ​dry ​environments; dependable ​application ​and ​maintenance
  • WIDE ​RANGE ​OF ​SIZES: Ensures ​correct ​fastener ​for ​effective ​results
  • FOR ​USE ​IN ​CONCRETE ​ONLY: Provides ​most ​consistent ​holding ​values; ​secure application
  • PACKAGED ​WITH​ ​NUTS ​AND ​WASHER: Fast, ​quick, ​complete ​installation
  • HOLE ​SIZE ​IS ​ANCHOR ​SIZE: Quick ​and ​easy ​installation; ​simple ​to ​order
Products specifications
Bit Size 1"
Minimum Embedment 4-1/2"
Thread Length 3"
Thread Type 1" - 8
2000 PSI Concrete - Pull-Out (lbs.) * 7329
2000 PSI Concrete - Shear (lbs.) * 17712
Type Male
Primary Concrete only
Diameter 1"
Length 6"
Material Carbon Steel Zinc Plated
Environment Dry
Box Qty 5
Minimum Spacing 10"
Minimum Edge Distance 5"
Maximum Fixture Thickness 1/2"
Minimum Fixture Hole Diameter (In Place) 1-1/4"
Minimum Fixture Hole Diameter (Hole Spotted) 1"
Length ID Code J
Maximum Torque 250 - 300 ft./lbs.
Wrench Size For Nut 1-1/2"
Length Measurement End to End
Brand Name CONFAST®
Application Video

Installation Video
Installing a 1" x 6" (six inches) Wedge Anchor Zinc Plated
  1. Drill a 1" hole into the concrete using a carbide-tipped bit that meets ANSI Standards B212.15.
  2. Drill the hole a 1/2" deeper than the anchor will penetrate the concrete, making sure the minimum embedment requirements of 4-1/2" is met.
  3. The hole can be drilled while the fixture is in place. The minimum hole in the fixture for the 1" x 6" (six inches) Wedge Anchor Zinc Plated is 1-1/4".
  4. Clean the hole with a wire brush, vacuum, compressed air, or a blow-out bulb.
  5. Put the nut and washer on the 1" x 6" (six inches) Wedge Anchor Zinc Plated, making sure the nut is on the last threads; this will protect the threads from damage when the wedge anchor is hammered into the hole and into the concrete.
  6. Insert the anchor through the hole in the fixture and into the hole in the base material.
  7. This should be a very tight fit. Then use a hammer to complete the installation until the nut and washer are tight against the fixture. It is important that the threads go below the surface of either the base material or the fixture.
  8. Turn the nut clockwise on the anchor until finger tight.
  9. Using a 1-1/2" wrench, turn the nut 3 to 4 times until snug or until the proper torque value of 250 - 300 ft./lbs. is reached.
  10. Always use proper personal protective equipment per manufacturer's and OSHA instructions.

Application Pictures
1" x 6" zinc plated wedge anchors - concrete - trash compactor receptacle
Product Reviews

* The figures above indicate average ultimate tension and shear failure values. A safety factor of 4:1 or 25% of ultimate value is generally accepted as a safe working load. Reference should always be made to applicable codes.



* The bits are recommended by diameter and may not necessarily be the length needed for your application. Please make sure the usable length will work for your application. *

Questions? Comments?
Contact Us

*
*
*