ITW/RedHead®
1" x 9" Red Head Trubolt Zinc Plated WS-10090, 5/Box
(No reviews yet)
Write a Review
- SKU:
- WA19;R
- UPC:
- 662520019339
- MPN:
- WS10090
- Availability:
- Discontinued by manufacturer, see page for alternatives.
Description
ITW/RedHead® - 1" x 9" Red Head Trubolt Wedge Anchor Zinc Plated
The 1" x 9" Red Head Trubolt Wedge Anchor Zinc Plated (5 pieces per box) are designed for fastening items to concrete. All orders will be received in 1 to 3 days when shipped in the Continental United States.
- Bit size 1"
- Minimum embedment 4-1/2"
- Thread Length 2-1/2"
- Zinc plated for indoor use
- Do not use in vibratory loads
- Packaged with zinc plated nuts and washers
- 1" inch diameter x 9" (nine inches) inch long
- Spacing must be a minimum of 10 anchor diameters
- Free freight on all orders over $25.00
Products specifications
| Bit Size | 1" |
| Country | American Made |
| Box Qty | 5 |
| Minimum Embedment | 4-1/2" |
| Wrench Size For Nut | 1-1/2" |
| Primary | Concrete only |
| Thread Type | 1" - 8 |
| Minimum Edge Distance | 7-7/8" |
| Maximum Fixture Thickness | 4-1/2" |
| Minimum Fixture Hole Diameter (In Place) | 1-1/8" |
| Minimum Fixture Hole Diameter (Hole Spotted) | 1" |
| Length ID Code | P |
| Brand Name | ITW/RedHead |
| Minimum Spacing | 15-3/4" |
| Maximum Torque | 300 ft./lbs. |
| Thread Length | 2-1/2" |
| 2000 PSI Concrete - Pull-Out (lbs.) * | 11770 |
| 2000 PSI Concrete - Shear (lbs.) * | 16080 |
| Length Measurement | End to End |
| Diameter | 1" |
| Length | 9" |
| Material | Carbon Steel Zinc Plated |
| Environment | Dry |
| Type | Male |
* Values shown are average ultimate values and are offered only as a guide and are not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe working load
Application Video
Installation Video
Installing a 1" x 9" (nine inches) Red Head Trubolt Wedge Anchor Zinc Plated - Select a carbide drill bit with a diameter equal to the anchor diameter. Drill a hole at least 1/4” deeper than nominal anchor embedment.
- Clean hole with pressurized air or vacuum to remove any excess dust/debris.
- Using the washer and nut provided, assemble the anchor, leaving nut one half turn from the end of the anchor to protect threads. Drive anchor through fixture to be fastened until washer is flush to surface of fixture.
- Expand anchor by tightening nut to the specified setting torque – see torque table (approx3 to 5 full revolutions).
- Warning! Use in concrete ONLY. Not recommended for use in lightweight masonry such as block or brick.
- Warning! Always wear safety glasses and other necessary protective devices or apparel when installing or working with anchors.
- Caution: Use of core drills is not recommended to drill holes for use with this anchor.
- Do not use an impact wrench to set or tighten the anchor. Not recommended for use in concrete which has not had sufficient time to cure.
- The use of carbide drill bits manufactured with ANSI B212.15 drill bit diameter requirements is recommended for installation of this anchor. Anchor spacing and edge distance (anchor installation locations) are the responsibility of the engineer of record.
- Installing product in oversized hole is not recommended. Product will not set properly or achieve full designed load in oversized hole.
Application Photos
Additional Information
Bit Size: |
1" |
Minimum Embedment: |
4-1/2" |
Thread Length: |
2-1/2" |
Primary: |
Concrete only |
Environment: |
Dry |
Thread Type: |
1" - 8 |
Type: |
Male |
Diameter: |
1" |
Length: |
9" |
Material: |
Carbon Steel Zinc Plated |
Box Qty: |
5 |
Maximum Fixture Thickness: |
4-1/2" |
Minimum Fixture Hole Diameter (In Place): |
1-1/8" |
Minimum Fixture Hole Diameter (Hole Spotted): |
1" |
Length ID Code: |
P |
Wrench Size For Nut: |
1-1/2" |
Length Measurement: |
End to End |
Brand Name: |
ITW/RedHead |
Related Products
Related Products
1" x 9" Wedge Anchor Zinc Plated, 5/Box
CONFAST®
$65.05
Products Features
ZINC PLATED: Helps prevent rust in dry environments; dependable application and maintenance
WIDE RANGE OF SIZES: Ensures correct fastener for...
1" x 9" Galvanized Wedge Anchor, 5/Box
CONFAST®
$138.47
Products Features HOT-DIPPED GALVANIZED: Helps prevent rusting in moist environments; lower maintenance AVAILABLE IN DIAMETERS FROM 3/8" TO 1-1/4": Ensures proper...
1" x 9" Stainless Steel Wedge Anchor, 5/Box
CONFAST®
$298.63
Products Features MADE FROM 304 STAINLESS STEEL: Can be used in wet, submerged environments and will not rust; lowered maintenance costs COMPLETE LINE: All...
1" x 9" 316 Stainless Steel U.S. Made ThunderStud Anchor, 5/Box
American Made ThunderStud®
$879.49
Products Features MADE IN AMERICA: Assures top quality and meets most Made in America requirements PATENTED UNIVERSAL CLIP: Anchor does not spin in the...
1" x 13-1/2" Hammer Bit, Each
TruCut®
$69.79
Products Features TRICARB® CARBIDE: Guarantees longer bit life and speedier penetration due to increased chiseling action THUNDERTWIST® FLUTE DESIGN: Faster dust removal allows...
1" x 13-1/8" SDS Bit, Each
TruCut®
$105.98
Products Features TRICARB® CARBIDE: Longer bit life and quick penetration due to increased chiseling action THUNDERTWIST® FLUTE DESIGN: Faster dust removal provides faster...