JavaScript seems to be disabled in your browser.
You must have JavaScript enabled in your browser for full functionality of this website.
You have no items in your shopping cart.
Free Shipping
$25 or more

1/4" x 3-1/4" Red Head Trubolt+ Wedge Anchor Zinc Plated, 100/Box

Not available
Presently Out of Stock

1/4" x 3-1/4" Red Head Trubolt+ Wedge Anchor Zinc Plated, 100/Box

Not available
Presently Out of Stock

Purchase the quality 1/4" x 3-1/4" Red Head Trubolt+ Wedge Anchor Zinc Plated today, in stock and ready for same day shipment. Most orders arrive in 1 to 3 business days. TB4C1432
Products Features
  • American ​Made: Quality ​assurance; ​domestic product
  • ICC-ES ​LISTED: Stringent ​testing ​ensures ​up-to-date ​standards in ​most ​applications
  • APPROVED ​FOR ​CRACKED ​CONCRETE: Application ​can ​progress ​regardless ​of ​​​concrete location ​where ​the ​anchor ​is ​installed
  • APPROVED ​FOR ​SEISMIC ​CONDITIONS: Anchor is more ​versatile and can be used in more applications
  • FULLY ​THREADED: Allows ​for ​use ​in ​a​ ​wide ​range ​of ​installations
Products specifications
Bit Size 1/4"
Minimum Embedment 1-3/4"
Thread Length Fully Threaded
Thread Type 1/4" - 20
Type Male
Primary Concrete only
Diameter 1/4"
Length 3-1/4"
Material Carbon Steel Zinc Plated
Environment Dry
Box Qty 100
Minimum Spacing See PDF
Minimum Edge Distance See PDF
Maximum Fixture Thickness See PDF
Minimum Fixture Hole Diameter (In Place) 3/8"
Minimum Fixture Hole Diameter (Hole Spotted) 1/4"
Length ID Code D+
Maximum Torque 8 ft./lbs.
Wrench Size For Nut 7/16"
Length Measurement End to End
Country American Made
Brand Name ITW/RedHead
Application Video

Installation Video
Installing a 1/4" x 3-1/4" Red Head Trubolt+ Wedge Anchor Zinc Plated
  1. Select a carbide drill bit with a diameter equal to the anchor diameter. Drill a hole at least 1/4" deeper than nominal anchor embedment.
  2. Clean hole with pressurized air or vacuum to remove any excess dust/debris.
  3. Using the washer and nut provided, assemble the anchor, leaving nut one half turn from the end of the anchor to protect threads. Drive anchor through fixture to be fastened until washer is flush to surface of fixture.
  4. Expand anchor by tightening nut to the specified setting torque - see torque table (approx3 to 5 full revolutions).
  5. Warning! Use in concrete ONLY. Not recommended for use in lightweight masonry such as block or brick.
  6. Warning! Always wear safety glasses and other necessary protective devices or apparel when installing or working with anchors.
  7. Caution: Use of core drills is not recommended to drill holes for use with this anchor.
  8. Do not use an impact wrench to set or tighten the anchor. Not recommended for use in concrete which has not had sufficient time to cure.
  9. The use of carbide drill bits manufactured with ANSI B212.15 drill bit diameter requirements is recommended for installation of this anchor. Anchor spacing and edge distance (anchor installation locations) are the responsibility of the engineer of record.
  10. Installing product in oversized hole is not recommended. Product will not set properly or achieve full designed load in oversized hole.

Product Video

Application Pictures
1/4" x 3-1/4" zinc plated wedge anchors - concrete - surveillance c camera
Product Reviews

* The figures above indicate average ultimate tension and shear failure values. A safety factor of 4:1 or 25% of ultimate value is generally accepted as a safe working load. Reference should always be made to applicable codes.

* The bits are recommended by diameter and may not necessarily be the length needed for your application. Please make sure the usable length will work for your application. *

These bits work with the selected anchor
Back to product

Questions? Comments?
Contact Us