CONFAST®

3/16" x 4" CONFAST® Mushroom Head Concrete Anchor, 100/Box

(No reviews yet) Write a Review
SKU:
SMH3164
UPC:
820274007006
Availability:
In Stock, Ships Today!
$32.09

Description

Products Features
  • PRE-EXPANDED – makes installation of anchor easy
  • MUSHROOM HEAD – Once installed anchor is tamper resistant
  • PREFORMED ANCHOR – No secondary tightening required
  • ZINC PLATED – Helps prevent rust.
Products specifications
Bit Size3/16"
Minimum Embedment1-1/4"
Box Qty100
2000 PSI Concrete - Pull-Out (lbs.) *432
2000 PSI Concrete - Shear (lbs.) *984
TypeMale
PrimaryLightweight Concrete
Diameter3/16"
Length4"
MaterialCarbon Steel Zinc Plated
EnvironmentDry
Minimum Spacing1-7/8'
Minimum Edge Distance1"
Maximum Fixture Thickness2-3/4"
Minimum Fixture Hole Diameter (In Place)1/4"
Length MeasurementUnderneath head
Brand Name CONFAST®
* Values shown are average ultimate values and are offered only as a guide and are not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe working load

Applications
The anchor is made from Carbon Steel, and is zinc plate. This anchor is designed for use in Lightweight Concrete

Environment
The anchor is designed for use in a dry environment.

Head Style
The anchor is a Mushroom Head head and is designed to allow the head to sit on top of the surface of the item being attached.

Hole Diameter/Bit Diameter
The anchor requires a 3/16" hole to be drilled in the base material (Lightweight Concrete). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor
The diameter of the anchor is 3/16".

Length Anchor
The length of the anchor is 4"

Minimum Embedment
The minimum anchor embedment into the concrete is 1-1/4". Therefore, the anchor must be installed so that a minimum of 1-1/4" of the anchor is embedded into the concrete.

Depth of Hole
The depth of the hole that is required for the anchor should be a minimum of 1/2" deeper than the anchor will penetrate the concrete. This will allow space for dust created during the installation process to fall, which will prevent the anchor from bottoming out in the hole before full penetration into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 2-3/4". This will ensure that the minimum embedment of 1-1/4" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 3/16" diameter anchor requires the hole in the fixture to be 1/4".

Spacing between Anchors
Each anchor must be spaced a minimum distance of 1-7/8' from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 1" from an unsupported edge of the concrete.

Holding Values - Ultimate Load Values in 2000 PSI Concrete

Anchor Size

Minimum Embedment

Pull-Out (lbs.)

Shear (lbs.)

3/16" x 4"

1-1/4"

432

984


Installation Procedure
Drill a hole into the base material to a depth of at least 1/2" deeper than the embedment required. The tolerances of the drill bit used should meet the requirements of ANSI Standard B212.15. Blow the hole clean of dust and other material.

Where a fixture is used, drive the anchor through the fixture into the anchor hole until the head is firmly seated against the fixture. Be sure the anchor is driven to the required embedment depth.

View AllClose

Additional Information

Bit Size:
3/16"
Minimum Embedment:
1-1/4"
Box Qty:
100
2000 PSI Concrete - Pull-Out (lbs.) *:
432
2000 PSI Concrete - Shear (lbs.) *:
984
Type:
Male
Primary:
Lightweight Concrete
Diameter:
3/16"
Length:
4"
Material:
Carbon Steel Zinc Plated
Environment:
Dry
Minimum Spacing:
1-7/8'
Minimum Edge Distance:
1"
Maximum Fixture Thickness:
2-3/4"
Minimum Fixture Hole Diameter (In Place):
1/4"
Length Measurement:
Underneath head
Brand Name:
CONFAST®
View AllClose