CONFAST®
3/8" x 5" CONFAST® Hex Head Concrete Screw , 25/Box
- SKU:
- CSH385
- Availability:
- In Stock, Ships Today!
Description
- COMPLETE LINE: Ensures correct product can be located and purchased for any job
- ALL LENGTHS ARE AVAILABLE: Using the correct length screw ensures quality, secure fastening
- SPECIAL THREADS: Decreases installation torque allowing screw to be installed faster and easier
| Bit Size | 3/8" |
| Minimum Embedment | 1-1/2" |
| Box Qty | 25 |
| Thread Type | Low Torque Threads |
| 2000 PSI Concrete - Pull-Out (lbs.) * | 1590 |
| 2000 PSI Concrete - Shear (lbs.) * | 2662 |
| Type | Male |
| Primary | Concrete |
| Diameter | 3/8" |
| Length | 5" |
| Material | Carbon Steel |
| Environment | Dry |
| Minimum Spacing | 6" |
| Minimum Edge Distance | 3" |
| Wrench Size For Nut | 9/16" |
| Length Measurement | Underneath head |
| Brand Name | CONFAST |
Applications
The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete
Environment
The anchor is designed for use in a dry environment.
Head Style
The anchor is a Hex Washer Serrated head and is designed to allow the head to sit on top of the surface of the item being attached.
Hole Diameter/Bit Diameter
The anchor requires a 3/8" hole to be drilled in the base material (Concrete). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.
Driver Required
A 9/16" is required for driving the anchor into the base material.
Diameter of Anchor
The diameter of the anchor is 3/8".
Length Anchor
The length of the anchor is 5"
Minimum Embedment
The minimum anchor embedment into the concrete is 1-1/2". Therefore, the anchor must be installed so that a minimum of 1-1/2" of the anchor is embedded into the concrete.
Depth of Hole
The depth of the hole that is required for the anchor should be a minimum of 1/2" deeper than the anchor will penetrate the concrete. This will allow space for dust created during the installation process to fall, which will prevent the anchor from bottoming out in the hole before full penetration into the concrete.
Wrench Size
The size of the wrench required to turn the nut to set the anchor is 9/16".
Spacing between Anchors
Each anchor must be spaced a minimum distance of 6" from each other when measured center to center.
Edge Distance
It is very important not to install the anchor any closer than 3" from an unsupported edge of the concrete.
|
Anchor Size |
Minimum Embedment |
Pull-Out (lbs.) |
Shear (lbs.) |
|
3/8" x 5" |
1-1/2" |
1590 |
2662 |
- Drill a 3/8" hole into the concrete using a carbide-tipped bit that meets ANSI Standards B212.15.
- Drill the hole a 1/2" deeper than the anchor will penetrate the concrete, making sure the minimum embedment requirements of 1" is met.
- Clean the hole with a wire brush, vacuum, compressed air, or a blow-out bulb.
- Insert the point of the 3/8" x 5" CONFAST® Hex Head Concrete Screw into the hole.
- Turn the screw clockwise, applying slight pressure until the head of the screw is snug against the material being fastened.
- Always use proper personal protective equipment per manufacturer's and OSHA instructions.
Additional Information
Bit Size: |
3/8" |
Minimum Embedment: |
1-1/2" |
Box Qty: |
25 |
Thread Type: |
Low Torque Threads |
2000 PSI Concrete - Pull-Out (lbs.) *: |
1590 |
2000 PSI Concrete - Shear (lbs.) *: |
2662 |
Type: |
Male |
Primary: |
Concrete |
Diameter: |
3/8" |
Length: |
5" |
Material: |
Carbon Steel |
Environment: |
Dry |
Minimum Spacing: |
6" |
Minimum Edge Distance: |
3" |
Wrench Size For Nut: |
9/16" |
Length Measurement: |
Underneath head |
Brand Name: |
CONFAST |
Related Products
1/4" x 5" Hex Head CONFAST® Concrete Screw, 100/Box
CONFAST®
3/16" x 4" Hex Head CONFAST® Concrete Screw, 100/Box
CONFAST®
1/4" x 2-3/4" Hex Head CONFAST® Concrete Screw, 100/Box
CONFAST®
3/16" x 2-3/4" Hex Head CONFAST® Concrete Screw, 100/Box
CONFAST®
3/16" x 3-1/4" Hex Head CONFAST® Concrete Screw, 100/Box
CONFAST®
1/4" x 3-3/4" Hex Head CONFAST® Concrete Screw, 100/Box
CONFAST®
