MKT

1-1/4" x 12" MKT Sup-R Stud® + Anchor, 5/Box

(No reviews yet) Write a Review
SKU:
WA11412;M
UPC:
8227543855
MPN:
2611412
Availability:
Call for availability
$367.36

Description

Products Features 
  • ZINC ​PLATED:  Helps ​prevent ​rust ​in ​dry ​environments; dependable ​application ​and ​maintenance 
  • WIDE ​RANGE ​OF ​SIZES:  Ensures ​correct ​fastener ​for ​effective ​results 
  • FOR ​USE ​IN ​CONCRETE ​ONLY:  Provides ​most ​consistent ​holding ​values; ​secure application 
  • PACKAGED ​WITH​ ​NUTS ​AND ​WASHER:  Fast, ​quick, ​complete ​installation 
  • HOLE ​SIZE ​IS ​ANCHOR ​SIZE:  Quick ​and ​easy ​installation; ​simple ​to ​order 

Applications 
The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.

Environment 
The anchor is designed for use in a dry environment.

Hole Diameter/Bit Diameter 
The anchor requires a 1-1/4" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor  
The diameter of the anchor is 1-1/4".

Length Anchor  
The length of the anchor is 12"

Thread Type  
The threads on the anchor are national coarse threads that measures 1-1/4" with 7 threads per inch, commonly referred to as 1-1/4"-7.

Thread Length
The length of the threads on the anchor is 3-1/4" in length.

Packaging 
The anchor is packaged with 5 pieces per box and is packaged with the correct number and diameter of nuts and washers.

Depth of Hole 
The depth of the hole that is required for the anchor should be a minimum of 1/2" deeper than the anchor will penetrate the concrete. This will allow space for dust created during the installation process to fall, which will prevent the anchor from bottoming out in the hole before full penetration into the concrete.

Wrench Size  
The size of the wrench required to turn the nut to set the anchor is 1-7/8".

Torque Value 
To be set properly in the concrete, the anchor must be torqued to between 200-350 ft./lbs.

Edge Distance
It is very important not to install the anchor any closer than 6-1/4" from an unsupported edge of the concrete.

Markings 
The anchor is stamped with the letter T on the threaded end to allow inspection of the anchor after installation. The letter "T" designates an overall length of the anchor as between 12" up to, but not including 13" in length.

Products Specifications 
Bit Size1-1/4"
Minimum EmbedmentSee PDF
Thread Length3-1/4"
PrimaryConcrete only
EnvironmentDry
Thread Type1-1/4" - 7
TypeMale
Diameter1-1/4"
Length12"
MaterialCarbon Steel Zinc Plated
Box Qty5
Minimum Spacing12-1/2"
Minimum Edge Distance6-1/4"
Maximum Fixture Thickness4-1/4"
Minimum Fixture Hole Diameter (In Place)1-3/8"
Minimum Fixture Hole Diameter (Hole Spotted)1-1/4"
Length ID CodeT
Maximum Torque200-350 ft./lbs.
Wrench Size For Nut1-7/8"
Length MeasurementEnd to End
Brand NameMKT
Application Video  

Downloads  

pdfTechnical Data

View AllClose

Additional Information

Bit Size:
1-1/4"
Minimum Embedment:
5-1/2"
Thread Length:
4"
Primary:
Concrete only
Environment:
Dry
Thread Type:
1-1/4" - 7
2000 PSI Concrete - Pull-Out (lbs.) *:
13162
2000 PSI Concrete - Shear (lbs.) *:
24206
Type:
Male
Diameter:
1-1/4"
Length:
12"
Material:
Carbon Steel Zinc Plated
Box Qty:
5
Minimum Spacing:
12-1/2"
Minimum Edge Distance:
6-1/4"
Maximum Fixture Thickness:
5-1/4"
Minimum Fixture Hole Diameter (In Place):
1-1/2"
Minimum Fixture Hole Diameter (Hole Spotted):
1-1/4"
Length ID Code:
T
Maximum Torque:
400 - 450 ft./lbs.
Wrench Size For Nut:
1-7/8"
Length Measurement:
End to End
Brand Name:
MKT
View AllClose