American Made ThunderStud®

1/2" x 10" Zinc Plated U.S. Made ThunderStud Anchor, 25/Box

(No reviews yet) Write a Review
SKU:
WA1210;T
UPC:
820274901182
MPN:
TS1210
Availability:
In Stock, Ships Today!
$69.65
Frequently bought together:

Description

Products Features 
  • MADE IN AMERICA: Assures top quality and meets most Made in America requirements
  • PATENTED UNIVERSAL CLIP: Anchor does not spin in the hole which makes each fastening faster and more secure
  • PARTIAL THREADS: Assures proper anchor length is used to meet minimum embedment depths
  • LENGTH I. D. STAMPED ON EACH ANCHOR: Provides for a fast easy inspection of embedment depth
Products specifications 
Bit Size 1/2"
Box Qty 25
Minimum Embedment 2-1/4"
Wrench Size For Nut 3/4"
Primary  Concrete only
Thread Type 1/2" - 13
Maximum Fixture Thickness 7"
Minimum Fixture Hole Diameter (In Place) 5/8"
Minimum Fixture Hole Diameter (Hole Spotted) 1/2"
Length ID Code  R
Brand Name  ThunderStud
Minimum Spacing 5"
Maximum Torque 50 - 60 ft./lbs.
Country  American Made
Thread Length 1-3/4"
2000 PSI Concrete - Pull-Out (lbs.) * 3999
2000 PSI Concrete - Shear (lbs.) * 7419
Length Measurement  End to End
Diameter 1/2"
Length 10"
Material  Carbon Steel Zinc Plated
Environment  Dry
Type  Male
Installation Video 
Installing a 1/2" x 10" Zinc Plated ThunderStud Wedge Anchor
  1. Drill a 1/2" hole into the concrete using a carbide-tipped bit that meets ANSI Standards B212.15.
  2. Drill the hole a 1/2" deeper than the anchor will penetrate the concrete, making sure the minimum embedment requirements of 2-1/4" is met.
  3. The hole can be drilled while the fixture is in place. The minimum hole in the fixture for the 1/2" x 10" Zinc Plated ThunderStud Wedge Anchor is 5/8".
  4. Clean the hole with a wire brush, vacuum, compressed air, or a blow-out bulb.
  5. Put the nut and washer on the 1/2" x 10" Zinc Plated ThunderStud Wedge Anchor, making sure the nut is on the last threads; this will protect the threads from damage when the wedge anchor is hammered into the hole and into the concrete.
  6. Insert the anchor through the hole in the fixture and into the hole in the base material.
  7. This should be a very tight fit. Then use a hammer to complete the installation until the nut and washer are tight against the fixture. It is important that the threads go below the surface of either the base material or the fixture.
  8. Turn the nut clockwise on the anchor until finger tight.
  9. Using a 3/4" wrench, turn the nut 3 to 4 times until snug or until the proper torque value of 50 - 60 ft./lbs. is reached.
  10. Always use proper personal protective equipment per manufacturer's and OSHA instructions.

View AllClose

Additional Information

Bit Size:
1/2"
Minimum Embedment:
2-1/4"
Thread Length:
1-3/4"
Primary:
Concrete only
Environment:
Dry
Thread Type:
1/2" - 13
2000 PSI Concrete - Pull-Out (lbs.) *:
3999
2000 PSI Concrete - Shear (lbs.) *:
7419
Type:
Male
Diameter:
1/2"
Length:
1"
Material:
Carbon Steel Zinc Plated
Box Qty:
25
Minimum Spacing:
5"
Maximum Fixture Thickness:
7"
Minimum Fixture Hole Diameter (In Place):
5/8"
Minimum Fixture Hole Diameter (Hole Spotted):
1/2"
Length ID Code:
R
Maximum Torque:
50 - 60 ft./lbs.
Wrench Size For Nut:
3/4"
Length Measurement:
End to End
Country:
American Made
Brand Name:
ThunderStud
View AllClose