Simpson Strong-Tie

1/2" x 13" Simpson Strong-Tie Titen HD Screw Anchor Zinc Plated - THD501300H, 5/Box

(No reviews yet) Write a Review
SKU:
CSH1213;SC
UPC:
707392600015
MPN:
THD501300H
Availability:
In Stock, Ships Today!
$162.63

Description

Products Features 
  • COMPLETE ​LINE:  Ensures ​correct ​product ​can ​be ​located ​and ​purchased ​for ​any ​job 
  • ALL ​LENGTHS ​ARE ​AVAILABLE:  Using ​the ​correct ​length ​screw ​ensures ​quality, ​secure ​fastening 
  • SPECIAL ​THREADS: Decreases ​installation ​torque ​allowing ​screw ​to ​be ​installed ​faster and ​easier 
  • TWO​ ​DIAMETERS:  ​3/16" ​and ​1/4" Choice ​allows ​for ​wider ​variety ​of ​fastening ​applications depending ​on ​the ​hole ​in ​the ​fixture ​being ​attached 
  • BIT ​INCLUDED ​IN ​EACH​ ​BOX:  Using the correct ​bit ​will give you ​better-​holding ​values 
Products specifications
Bit Size1/2"
Box Qty5
Thread TypeSerrated Teeth
TypeMale
PrimaryConcrete & Grout Filled CMU
Diameter1/2"
Length13"
MaterialCarbon Steel
EnvironmentDry
Minimum Spacing3"
Minimum Edge Distance1-3/4"
Minimum Fixture Hole Diameter (In Place)11/16"
Minimum Fixture Hole Diameter (Hole Spotted)11/16"
Length ID Code13
Wrench Size For Nut3/4"
Length MeasurementUnderneath head
Brand NameSimpson Strong-Tie
* Values shown are average ultimate values and are offered only as a guide and are not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe working load

Applications
The anchor is made from Grade 10B21 SAEJ403, ASTM B633, and is Zinc Plated. This anchor is designed for use in Concrete & Grout Filled CMU

Environment
The anchor is designed for use in a dry environment.

Head Style
The anchor is a Hex Washer Serrated head and is designed to allow the head to sit on top of the surface of the item being attached.

Hole Diameter/Bit Diameter
The anchor requires a 1/2" hole to be drilled in the base material (Concrete & Grout Filled CMU). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Driver Required
A 3/4" is required for driving the anchor into the base material.

Diameter of Anchor
The diameter of the anchor is 1/2".

Length Anchor
The length of the anchor is 13"

Depth of Hole
The depth of the hole that is required for the anchor should be a minimum of 1/2" deeper than the anchor will penetrate the concrete. This will allow space for dust created during the installation process to fall, which will prevent the anchor from bottoming out in the hole before full penetration into the concrete.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 1/2" diameter anchor requires the hole in the fixture to be 11/16".

Wrench Size
The size of the wrench required to turn the nut to set the anchor is 3/4".

Spacing between Anchors
Each anchor must be spaced a minimum distance of 3" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 1-3/4" from an unsupported edge of the concrete.

Markings
The anchor is stamped with the letter 13 on the threaded end to allow inspection of the anchor after installation. The letter "13" designates an overall length of the anchor as between 13" up to, but not including 14" in length.

Installing a 1/2" x 13" Simpson Strong-Tie Titen HD Screw Anchor Zinc Plated (ea) THD501300H
  1. Drill a 1/2" hole into the concrete using a carbide-tipped bit that meets ANSI Standards B212.15.
  2. Drill the hole a 1/2" deeper than the anchor will penetrate the concrete, making sure the minimum embedment requirements of 1" is met.
  3. Clean the hole with a wire brush, vacuum, compressed air, or a blow-out bulb.
  4. Insert the point of the 1/2" x 13" Simpson Strong-Tie Titen HD Screw Anchor Zinc Plated (ea) THD501300H into the hole. Make sure that the screw being installed will penetrate the base material a minimum of 1" but no deeper than 1-3/4".
  5. Turn the screw clockwise, applying slight pressure until the head of the screw is snug against the material being fastened.
  6. Always use proper personal protective equipment per manufacturer's and OSHA instructions.

View AllClose

Additional Information

Bit Size:
1/2"
Environment:
Dry
Material:
Carbon Steel Zinc Plated
Thread Type:
Serrated Teeth
Type:
Male
Primary:
Concrete & Grout Filled CMU
Diameter:
1/2"
Length:
13"
Box Qty:
5
Minimum Spacing:
3"
Minimum Edge Distance:
1-3/4"
Minimum Fixture Hole Diameter (In Place):
11/16"
Minimum Fixture Hole Diameter (Hole Spotted):
11/16"
Length ID Code:
13
Wrench Size For Nut:
3/4"
Head Type:
Hex Washer Serrated
Length Measurement:
Underneath head
Driver Size:
3/4"
Brand Name:
Simpson Strong-Tie
View AllClose