ITW/RedHead®

1/2" x 5-1/2" Red Head Trubolt Zinc Plated WS-1254, 25/Box

(No reviews yet) Write a Review
SKU:
WA12512;R
UPC:
662520019537
MPN:
WS1254
Availability:
In Stock, Ships Today!
$41.60
Frequently bought together:

Description

ITW/RedHead® - 1/2" X 5-1/2" Trubolt® Wedge Anchor

The 1/2" X 5-1/2" Trubolt® Wedge Anchor (25 pieces per box) are designed for fastening items to concrete. All orders will be received in 1 to 3 days when shipped in the Continental United States.

  • Bit size 1/2"
  • Minimum embedment 2-1/4"
  • Thread Length 3"
  • Zinc plated for indoor use
  • Do not use in vibratory loads
  • Packaged with zinc plated nuts and washers
  • 1/2" inch diameter x 5-1/2" inch long
  • Spacing must be a minimum of 10 anchor diameters
  • Free freight on all orders over $25.00
Products specifications 
Bit Size 1/2"
Box Qty 25
Minimum Embedment 2-1/4"
Wrench Size For Nut 3/4"
Primary  Concrete only
Thread Type 1/2" - 13
Minimum Edge Distance 3-15/16"
Maximum Fixture Thickness 2-3/4"
Minimum Fixture Hole Diameter (In Place) 9/16"
Minimum Fixture Hole Diameter (Hole Spotted) 1/2"
Length ID Code I
Brand Name  ITW/RedHead
Minimum Spacing 7-7/8"
Maximum Torque 55 ft./lbs.
Country  American Made
Thread Length 4"
2000 PSI Concrete - Pull-Out (lbs.) * 2925
2000 PSI Concrete - Shear (lbs.) * 2855
Length Measurement  End to End
Diameter 1/2"
Length 5-1/2"
Material  Carbon Steel Zinc Plated
Environment  Dry
Type  Male
* Values shown are average ultimate values and are offered only as a guide and are not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe working load
Application Video 

Installation Video 
Installing a 1/2" x 5-1/2" Trubolt® Wedge Anchor
  1. Drill a 1/2" hole into the concrete using a carbide tipped bit that meets ANSI Standards B212.15.
  2. Drill the hole a 1/2" deeper than the anchor will penetrate the concrete, making sure the minimum embedment requirements of 2-1/4" is met.
  3. The hole can be drilled while the fixture is in place. The minimum hole in the fixture for the 1/2" x 5-1/2" Trubolt® Wedge Anchor is 9/16".
  4. Clean the hole with a wire brush, vacuum, compressed air, or a blow-out bulb.
  5. Put the nut and washer on the 1/2" x 5-1/2" Trubolt® Wedge Anchor, making sure the nut is on the last threads; this will protect the threads from damage when the wedge anchor is hammered into the hole and into the concrete.
  6. Insert the anchor through the hole in the fixture and into the hole in the base material.
  7. This should be a very tight fit. Then use a hammer to complete the installation until the nut and washer are tight against the fixture. It is important that the threads go below the surface of either the base material or the fixture.
  8. Turn the nut clockwise on the anchor until finger tight.
  9. Using a 3/4" wrench, turn the nut 3 to 4 times until snug or until the proper torque value of 55 ft./lbs. is reached.
  10. Always use proper personal protective equipment per manufacturers and OSHA instructions.

Application Photos 
1/2" x 5-1/2" zinc plated wedge anchors - concrete -painted fence post
View AllClose

Additional Information

Bit Size:
1/2"
Minimum Embedment:
2-1/4"
Thread Length:
3"
Primary:
Concrete only
Environment:
Dry
Thread Type:
1/2" - 13
3000 PSI Concrete - Pull-Out (lbs.) *:
2925
3000 PSI Concrete - Shear (lbs.) *:
2855
Type:
Male
Diameter:
1/2"
Length:
5-1/2"
Material:
Carbon Steel Zinc Plated
Box Qty:
25
Maximum Fixture Thickness:
2-3/4"
Minimum Fixture Hole Diameter (In Place):
9/16"
Minimum Fixture Hole Diameter (Hole Spotted):
1/2"
Length ID Code:
I
Wrench Size For Nut:
3/4"
Length Measurement:
End to End
Brand Name:
ITW/RedHead
View AllClose