Simpson Strong-Tie

1/4" x 3-1/4" Strong-Bolt® 2 316 Stainless Steel, 100/Box

(No reviews yet) Write a Review
SKU:
WAS-31614314;SC
UPC:
707392919902
MPN:
STB2-253146SS
Availability:
In Stock, Ships Today!
$512.42

Description

  • Code listed under IBC/IRC for cracked and uncracked concrete per ICC-ES ESR-3037 
  • Code listed under IBC/IRC for masonry per IAPMO UES ER-240 
  • Qualified for static and seismic loading conditions (seismic design categories A through F) 
  • Suitable for horizontal, vertical and overhead applications 
  • Qualified for minimum concrete thickness of 3 1/4", and lightweight concrete-over-metal deck thickness of 2 1/2" and 3 1/4" 
  • Standard (ANSI) fractional sizes: fits standard fixtures and installs with common drill bit and tool sizes 
  • Tested per ACI355.2 and AC193 

Applications 
The anchor is made from 316 Stainless Steel. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.

Environment 
The anchor is designed for use in a submerged/chemicals environment.

Hole Diameter/Bit Diameter 
 
The anchor requires a 1/4" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor  
The diameter of the anchor is 1/4".

Length Anchor  
The length of the anchor is 3-1/4"

Thread Type  
The threads on the anchor are national coarse threads that measures 1/4" with 20 threads per inch, commonly referred to as 1/4"-20.

Thread Length 
The length of the threads on the anchor is 2-7/16" in length.

Packaging 
The anchor is packaged with 100 pieces per box and is packaged with the correct number and diameter of nuts and washers.

Depth of Hole 
The depth of the hole that is required for the anchor should be a minimum of 1/2" deeper than the anchor will penetrate the concrete. This will allow space for dust created during the installation process to fall, which will prevent the anchor from bottoming out in the hole before full penetration into the concrete.

Fixture Hole Diameter 
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 1/4" diameter anchor requires the hole in the fixture to be 5/16".

Wrench Size  
The size of the wrench required to turn the nut to set the anchor is 7/16".

Torque Value 
To be set properly in the concrete, the anchor must be torqued to between 4 ft./lbs.

Markings 
The anchor is stamped with the letter D on the threaded end to allow inspection of the anchor after installation. The letter "D" designates an overall length of the anchor as between 3" up to, but not including 3-1/2" in length.

Products Specifications 
Bit Size1/4"
Minimum EmbedmentSee PDF
Thread Length2-7/16"
PrimaryConcrete only
EnvironmentSubmerged/Chemicals
Thread Type1/4" - 20
TypeMale
Diameter1/4"
Length3-1/4"
Material316 Stainless Steel
Box Qty100
Minimum SpacingSee PDF
Minimum Edge DistanceSee PDF
Maximum Fixture ThicknessSee PDF
Minimum Fixture Hole Diameter (In Place)5/16"
Minimum Fixture Hole Diameter (Hole Spotted)1/4"
Length ID CodeD
Maximum Torque4 ft./lbs.
Wrench Size For Nut7/16"
Length MeasurementEnd to End
Brand NameSimpson Strong-Tie®
Concrete ApplicationCracked & Uncracked Approved
View AllClose

Additional Information

Bit Size:
1/4"
Minimum Embedment:
1-1/8"
Thread Length:
2-1/8"
Primary:
Concrete only
Environment:
Submerged/Chemicals
Thread Type:
1/4" - 20
2000 PSI Concrete - Pull-Out (lbs.) *:
877
2000 PSI Concrete - Shear (lbs.) *:
1082
Type:
Male
Diameter:
1/4"
Length:
3-1/4"
Material:
316 Stainless Steel
Box Qty:
100
Minimum Spacing:
2-1/2"
Minimum Edge Distance:
1-1/4"
Maximum Fixture Thickness:
1-7/8"
Minimum Fixture Hole Diameter (In Place):
5/16"
Minimum Fixture Hole Diameter (Hole Spotted):
1/4"
Length ID Code:
E
Maximum Torque:
5 - 10 ft./lbs.
Wrench Size For Nut:
7/16"
Length Measurement:
End to End
Brand Name:
CONFAST
View AllClose