ITW/RedHead®

1/2" x 7" Red Head Trubolt Hot-Dipped Galvanized WS-1270G, 25/Box

(No reviews yet) Write a Review
SKU:
WAG127;R
UPC:
662520025385
MPN:
WS-1270G
Availability:
In Stock, Ships Today!
$108.39
Frequently bought together:

Description

ITW/RedHead® - 1/2" x 7" Red Head Trubolt Hot Dip Galvanized Wedge Anchor

The CONFAST® 1/2" x 7" (seven inches) Hot-Dipped Galvanized Wedge Anchor (25 pieces per box) are designed for fastening to concrete. All orders ship immediately from the Cleveland, Ohio warehouse for delivery in 1 to 3 days.

  • Bit size 1/2" 
  • Minimum embedment 2-1/4" 
  • Thread Length 5-1/2" 
  • 304 stainless steel clip 
  • Hot-Dipped Galvanized for use in moist environments 
  • For use in non-vibratory loading applications 
  • Packaged with hot-dipped galvanized nuts and washers 
  • 1/2" thick x 7" (seven inches) overall length 
  • Spacing between anchors is a minimum of 10 anchor diameters 
  • Free shipping on orders over $25.00 
Products specifications 
Bit Size 1/2" 
Box Qty 25 
Minimum Embedment 2-1/4" 
Wrench Size For Nut 3/4" 
Primary Concrete only 
Thread Type 1/2" - 13 
Minimum Edge Distance 3-15/16" 
Maximum Fixture Thickness 4-3/4" 
Minimum Fixture Hole Diameter (In Place) 9/16" 
Minimum Fixture Hole Diameter (Hole Spotted) 1/2" 
Length ID Code 
Brand Name ITW/RedHead 
Minimum Spacing 7-7/8" 
Maximum Torque 55 ft./lbs. 
Country American Made 
Thread Length 5-1/2" 
2000 PSI Concrete - Pull-Out (lbs.) * 3455 
2000 PSI Concrete - Shear (lbs.) * 4760 
Length Measurement End to End 
Diameter 1/2" 
Length 7" 
Material Hot-Dipped Galvanized 
Environment Damp 
Type Male 
Application Video 

Installation Video 
Installing a 1/2" x 7" (seven inches) Red Head Trubolt Hot Dip Galvanized Wedge Anchor 
  1. Select a carbide drill bit with a diameter equal to the anchor diameter. Drill a hole at least 1/4” deeper than nominal anchor embedment. 
  2. Clean hole with pressurized air or vacuum to remove any excess dust/debris. 
  3. Using the washer and nut provided, assemble the anchor, leaving nut one half turn from the end of the anchor to protect threads. Drive anchor through fixture to be fastened until washer is flush to surface of fixture. 
  4. Expand anchor by tightening nut to the specified setting torque – see torque table (approx3 to 5 full revolutions). 
  5. Warning! Use in concrete ONLY. Not recommended for use in lightweight masonry such as block or brick. 
  6. Warning! Always wear safety glasses and other necessary protective devices or apparel when installing or working with anchors. 
  7. Caution: Use of core drills is not recommended to drill holes for use with this anchor. 
  8. Do not use an impact wrench to set or tighten the anchor. Not recommended for use in concrete which has not had sufficient time to cure. 
  9. The use of carbide drill bits manufactured with ANSI B212.15 drill bit diameter requirements is recommended for installation of this anchor. Anchor spacing and edge distance (anchor installation locations) are the responsibility of the engineer of record. 
  10. Installing product in oversized hole is not recommended. Product will not set properly or achieve full designed load in oversized hole. 

Application Photos 
1/2" x 7" hot dipped galvanized wedge anchor - concrete - bike security
View AllClose

Additional Information

Bit Size:
1/2"
Minimum Embedment:
2-1/4"
Primary:
Concrete only
Environment:
Damp
Thread Type:
1/2" - 13
Type:
Male
Diameter:
1/2"
Length:
7"
Material:
Galvanized
Box Qty:
25
Maximum Fixture Thickness:
4-3/4"
Minimum Fixture Hole Diameter (In Place):
9/16"
Minimum Fixture Hole Diameter (Hole Spotted):
1/2"
Length ID Code:
L
Wrench Size For Nut:
3/4"
Length Measurement:
End to End
Country:
American Made
Brand Name:
ITW/RedHead
View AllClose