ITW/Buildex®

3/16" x 1-1/4" Tapcon Flat Phillips 410 Stainless Steel Silver Climaseal® Coated SPF3-114, 100/Box

(No reviews yet) Write a Review
SKU:
TCFS316114
UPC:
092097957725
MPN:
SPF3-114
Availability:
In Stock, Ships Today!
$76.36
Frequently bought together:

Description

Applications 
The anchor is made from 410 Stainless Steel, and is Silver Climaseal® Coated. This anchor is designed for use in Concrete, Block, and Brick.

Environment 
The anchor is designed for use in a moist environment.

Head Style 
The anchor is a Flat Countersunk Phillips head and is designed to prevent the head from protruding above the surface of the item being attached.

Hole Diameter/Bit Diameter 
The anchor requires a 5/32" hole to be drilled in the base material (Concrete, Block, and Brick). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Driver Required 
A #2 is required for driving the anchor into the base material.

Diameter of Anchor 
The diameter of the anchor is 3/16".

Length Anchor 
The length of the anchor is 1-1/4"

Thread Length 
The length of the threads on the anchor is 1-1/4" in length.

Packaging 
The anchor is packaged with 100 pieces per box and one (1) correct sized carbide bit.

Minimum Embedment 
The minimum anchor embedment into the concrete is 1". Therefore, the anchor must be installed so that a minimum of 1" of the anchor is embedded into the concrete.

Depth of Hole 
The depth of the hole that is required for the anchor should be a minimum of 1/2" deeper than the anchor will penetrate the concrete. This will allow space for dust created during the installation process to fall, which will prevent the anchor from bottoming out in the hole before full penetration into the concrete.

Maximum Fixture Thickness 
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 1/4". This will ensure that the minimum embedment of 1" will be met.

Fixture Hole Diameter 
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 3/16" diameter anchor requires the hole in the fixture to be 1/4".

Edge Distance 
It is very important not to install the anchor any closer than 2-1/4" from an unsupported edge of the concrete.

Bolt Length 
When a bolt is used in conjunction with the anchor, the length of the bolt needed is determined by considering these factors:

  • Flush With Concrete  - when the anchor is set flush with the surface of the concrete, add the thickness of the material being fastened to the thread length of 1-1/4", and then add the space for any washers used.
  • Below Surface of Concrete  - add the depth below the surface of the concrete to the thickness of the material being fastened, then add the space for the washer, and, finally, add 1-1/4" for the thread engagement.

Holding Values - Ultimate Load Values in 2000 PSI Concrete

Anchor Size

Minimum Embedment

Pull-Out (lbs.)

Shear (lbs.)

3/16" x 1-1/4"

1"

600

720

 

Products specifications 
Bit Size 5/32"
Minimum Embedment 1"
Thread Length 1-3/4"
Environment  Moist
Material  410 Stainless Steel Silver Climaseal® Coated
Thread Type  Hi-Lo
Type  Male
Diameter 3/16"
Length 2-1/4"
Box Qty 100
Minimum Spacing 3"
Minimum Edge Distance 2-1/4"
Maximum Fixture Thickness 1-1/4"
Minimum Fixture Hole Diameter (In Place) 1/4"
Minimum Fixture Hole Diameter (Hole Spotted) 1/4"
Head Type  Hex Washer
Length Measurement  Underneath head
Driver Size 1/4"
Product Type  Concrete Screw
* Values shown are average ultimate values and are offered only as a guide and are not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe working load
View AllClose

Additional Information

Bit Size:
5/32"
Minimum Embedment:
1"
Thread Length:
1-1/4"
Environment:
Moist
Material:
410 Stainless Steel Silver Climaseal® Coated
Thread Type:
Hi-Lo
2000 PSI Concrete - Pull-Out (lbs.) *:
600
2000 PSI Concrete - Shear (lbs.) *:
720
Type:
Male
Diameter:
3/16"
Length:
1-1/4"
Box Qty:
100
Minimum Spacing:
3"
Minimum Edge Distance:
2-1/4"
Maximum Fixture Thickness:
1/4"
Minimum Fixture Hole Diameter (In Place):
1/4"
Minimum Fixture Hole Diameter (Hole Spotted):
1/4"
Length Measurement:
Overall length including head
Driver Size:
#2
Brand Name:
ITW/Buildex
View AllClose