Simpson Strong-Tie

3/8" x 3" Simpson Strong-Tie Titen HD Countersunk Head Heavy-Duty Screw Anchor Zinc Plated, 50/Box

(No reviews yet) Write a Review
SKU:
CSF383;SC
UPC:
707392003205
MPN:
THD37300CS
Availability:
In Stock, Ships Today!
$185.55

Description

Products Features 
  • COMPLETE ​LINE:  Ensures ​correct ​product ​can ​be ​located ​and ​purchased ​for ​any ​job 
  • ALL ​LENGTHS ​ARE ​AVAILABLE:  Using ​the ​correct ​length ​screw ​ensures ​quality, ​secure ​fastening 
  • SPECIAL ​THREADS: Decreases ​installation ​torque ​allowing ​screw ​to ​be ​installed ​faster and ​easier 
  • TWO​ ​DIAMETERS:  ​3/16" ​and ​1/4" Choice ​allows ​for ​wider ​variety ​of ​fastening ​applications depending ​on ​the ​hole ​in ​the ​fixture ​being ​attached 
  • BIT ​INCLUDED ​IN ​EACH​ ​BOX:  Using the correct ​bit ​will give you ​better-​holding ​values 
Products specifications
Bit Size3/8"
Minimum EmbedmentSee PDF
Box Qty50
Thread TypeUndercut Design
TypeMale
Diameter3/8"
Length3"
MaterialCarbon Steel
EnvironmentDry
Minimum SpacingSee PDF
Minimum Edge DistanceSee PDF
Minimum Fixture Hole Diameter (In Place)1/2"
Minimum Fixture Hole Diameter (Hole Spotted)1/2"
Maximum TorqueSee PDF
Length MeasurementOverall length including head
Brand NameSimpson Strong-Tie
* Values shown are average ultimate values and are offered only as a guide and are not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe working load

Applications
The anchor is made from Carbon Steel, and is zinc plate. This anchor is designed for use in

Environment
The anchor is designed for use in a dry environment.

Head Style
The anchor is a Countersunk head and is designed to prevent the head from protruding above the surface of the item being attached.

Hole Diameter/Bit Diameter
The anchor requires a 3/8" hole to be drilled in the base material (). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Driver Required
A T50 is required for driving the anchor into the base material.

Diameter of Anchor
The diameter of the anchor is 3/8".

Length Anchor
The length of the anchor is 3"

Depth of Hole
The depth of the hole that is required for the anchor should be a minimum of 1/2" deeper than the anchor will penetrate the concrete. This will allow space for dust created during the installation process to fall, which will prevent the anchor from bottoming out in the hole before full penetration into the concrete.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 3/8" diameter anchor requires the hole in the fixture to be 1/2".

Torque Value
To be set properly in the concrete, the anchor must be torqued to between See PDF

Installing a 3/8" x 3" Simpson Strong-Tie Titen HD Countersunk Head Screw Anchor Zinc Plated (ea) TH37300CS
  1. Drill a 3/8" hole into the concrete using a carbide-tipped bit that meets ANSI Standards B212.15.
  2. Drill the hole a 1/2" deeper than the anchor will penetrate the concrete, making sure the minimum embedment requirements of 1" is met.
  3. Clean the hole with a wire brush, vacuum, compressed air, or a blow-out bulb.
  4. Insert the point of the 3/8" x 3" Simpson Strong-Tie Titen HD Countersunk Head Screw Anchor Zinc Plated (ea) TH37300CS into the hole. Make sure that the screw being installed will penetrate the base material a minimum of 1" but no deeper than 1-3/4".
  5. Turn the screw clockwise, applying slight pressure until the head of the screw is snug against the material being fastened.
  6. Always use proper personal protective equipment per manufacturer's and OSHA instructions.

View AllClose

Additional Information

Bit Size:
3/8"
Minimum Embedment:
See PDF
Environment:
Dry
Material:
Carbon Steel
Thread Type:
Undercut Design
Type:
Male
Diameter:
3/8"
Length:
3"
Box Qty:
50
Minimum Spacing:
See PDF
Minimum Edge Distance:
See PDF
Minimum Fixture Hole Diameter (In Place):
1/2"
Minimum Fixture Hole Diameter (Hole Spotted):
1/2"
Length Measurement:
Overall length including head
Brand Name:
Simpson Strong-Tie
Concrete Application:
Cracked & Uncracked Approved
Head Type:
Countersunk Phillips
View AllClose