ITW/RedHead®

3/4" x 8-1/2" Red Head Trubolt+ Anchor Zinc Plated, 10/Box

(No reviews yet) Write a Review
SKU:
TB4C3484
UPC:
662520173482
MPN:
TB4C-3484
Availability:
Contact us for information, see page for alternatives.
$35.30

OUT OF STOCK

Description

Products Features 
  • American ​Made:  Quality ​assurance; ​domestic product 
  • ICC-ES ​LISTED:  Stringent ​testing ​ensures ​up-to-date ​standards in ​most ​applications 
  • APPROVED ​FOR ​CRACKED ​CONCRETE: Application ​can ​progress ​regardless ​of ​​​concrete location ​where ​the ​anchor ​is ​installed 
  • APPROVED ​FOR ​SEISMIC ​CONDITIONS:  Anchor is more ​versatile and can be used in more applications 
  • FULLY ​THREADED:  Allows ​for ​use ​in ​a​ ​wide ​range ​of ​installations 
Products specifications 
Bit Size 3/4" 
Box Qty 10 
Minimum Embedment 4-1/2" 
Wrench Size For Nut 1-1/8" 
Primary Concrete only 
Thread Type 3/4" - 10 
Minimum Edge Distance See PDF 
Maximum Fixture Thickness See PDF 
Minimum Fixture Hole Diameter (In Place) 7/8" 
Minimum Fixture Hole Diameter (Hole Spotted) 3/4" 
Length ID Code O+ 
Brand Name ITW/RedHead 
Minimum Spacing See PDF 
Maximum Torque 100 ft./lbs. 
Thread Length Fully Threaded 
Length Measurement End to End 
Diameter 3/4" 
Length 8-1/2" 
Material Carbon Steel Zinc Plated 
Environment Dry 
Type Male 
* Values shown are average ultimate values and are offered only as a guide and are not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe working load
Application Video 

Installation Video 
Installing a 3/4" x 8-1/2" Red Head Trubolt+ Wedge Anchor Zinc Plated 
  1. Select a carbide drill bit with a diameter equal to the anchor diameter. Drill a hole at least 1/4" deeper than nominal anchor embedment. 
  2. Clean hole with pressurized air or vacuum to remove any excess dust/debris. 
  3. Using the washer and nut provided, assemble the anchor, leaving nut one half turn from the end of the anchor to protect threads. Drive anchor through fixture to be fastened until washer is flush to surface of fixture. 
  4. Expand anchor by tightening nut to the specified setting torque - see torque table (approx3 to 5 full revolutions). 
  5. Warning! Use in concrete ONLY. Not recommended for use in lightweight masonry such as block or brick. 
  6. Warning! Always wear safety glasses and other necessary protective devices or apparel when installing or working with anchors. 
  7. Caution: Use of core drills is not recommended to drill holes for use with this anchor. 
  8. Do not use an impact wrench to set or tighten the anchor. Not recommended for use in concrete which has not had sufficient time to cure. 
  9. The use of carbide drill bits manufactured with ANSI B212.15 drill bit diameter requirements is recommended for installation of this anchor. Anchor spacing and edge distance (anchor installation locations) are the responsibility of the engineer of record. 
  10. Installing product in oversized hole is not recommended. Product will not set properly or achieve full designed load in oversized hole. 

View AllClose

Additional Information

Bit Size:
3/4"
Thread Length:
Fully Threaded
Primary:
Concrete only
Environment:
Dry
Thread Type:
3/4" - 10
Type:
Male
Diameter:
3/4"
Length:
8-1/2"
Material:
Carbon Steel Zinc Plated
Box Qty:
10
Minimum Fixture Hole Diameter (In Place):
7/8"
Minimum Fixture Hole Diameter (Hole Spotted):
3/4"
Length ID Code:
O+
Maximum Torque:
100 ft./lbs.
Wrench Size For Nut:
1-1/8"
Length Measurement:
End to End
Country:
American Made
Brand Name:
ITW/RedHead
View AllClose