MKT
5/8" x 4-1/2" MKT Sup-R Stud® V Anchor, 25/Box
- SKU:
- WA58412;MV
- MPN:
- 2458412
- Availability:
- Call for availability
Description
- ZINC PLATED: Helps prevent rust in dry environments; dependable application and maintenance
- WIDE RANGE OF SIZES: Ensures correct fastener for effective results
- FOR USE IN CONCRETE ONLY: Provides most consistent holding values; secure application
- PACKAGED WITH NUTS AND WASHER: Fast, quick, complete installation
- HOLE SIZE IS ANCHOR SIZE: Quick and easy installation; simple to order
Applications
The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.
Environment
The anchor is designed for use in a dry environment.
Hole Diameter/Bit Diameter
The anchor requires a 5/8" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.
Diameter of Anchor
The diameter of the anchor is 5/8".
Length Anchor
The length of the anchor is 4-1/2"
Thread Type
The threads on the anchor are national coarse threads that measures 5/8" with 11 threads per inch, commonly referred to as 5/8"-11.
Thread Length
The length of the threads on the anchor is 2-1/2" in length.
Packaging
The anchor is packaged with 25 pieces per box and is packaged with the correct number and diameter of nuts and washers.
Depth of Hole
The depth of the hole that is required for the anchor should be a minimum of 1/2" deeper than the anchor will penetrate the concrete. This will allow space for dust created during the installation process to fall, which will prevent the anchor from bottoming out in the hole before full penetration into the concrete.
Wrench Size
The size of the wrench required to turn the nut to set the anchor is 15/16".
Torque Value
To be set properly in the concrete, the anchor must be torqued to between 100 ft./lbs.
Markings
The anchor is stamped with the letter G on the threaded end to allow inspection of the anchor after installation. The letter "G" designates an overall length of the anchor as between 4-1/2" up to, but not including 5" in length.
| Bit Size | 5/8" |
| Minimum Embedment | See PDF |
| Thread Length | 2-1/2" |
| Primary | Concrete only |
| Environment | Dry |
| Thread Type | 5/8" - 11 |
| Type | Male |
| Diameter | 5/8" |
| Length | 4-1/2" |
| Material | Carbon Steel Zinc Plated |
| Box Qty | 25 |
| Minimum Spacing | See PDF |
| Minimum Edge Distance | See PDF |
| Maximum Fixture Thickness | 1/2" |
| Minimum Fixture Hole Diameter (In Place) | 11/16" |
| Minimum Fixture Hole Diameter (Hole Spotted) | 5/8" |
| Length ID Code | G |
| Maximum Torque | 100 ft./lbs. |
| Wrench Size For Nut | 15/16" |
| Length Measurement | End to End |
| Brand Name | MKT |
Technical DataAdditional Information
Bit Size: |
5/8" |
Minimum Embedment: |
2-3/4" |
Thread Length: |
2-3/4" |
Primary: |
Concrete only |
Environment: |
Dry |
2000 PSI Concrete - Pull-Out (lbs.) *: |
3749 |
2000 PSI Concrete - Shear (lbs.) *: |
6198 |
Type: |
Male |
Diameter: |
5/8" |
Length: |
4-1/2" |
Material: |
Carbon Steel Zinc Plated |
Box Qty: |
25 |
Minimum Edge Distance: |
3-1/8" |
Maximum Fixture Thickness: |
1-1/8" |
Minimum Fixture Hole Diameter (In Place): |
7/8" |
Minimum Fixture Hole Diameter (Hole Spotted): |
5/8" |
Length ID Code: |
G |
Maximum Torque: |
75 - 90 ft./lbs. |
Wrench Size For Nut: |
15/16" |
Length Measurement: |
End to End |
Brand Name: |
MKT |
