Simpson Strong-Tie

5/8" x 6" Wedge-All® 316 Stainless Steel, 20/Box

(No reviews yet) Write a Review
SKU:
WAS-316586;S
MPN:
WA626006SS
Availability:
In Stock, Ships Today!
$408.67
Frequently bought together:

Description

  • Code listed under IBC/IRC for grout-filled CMU per ICC-ES ESR-1396
  • One-piece, wrap-around clip ensures uniform holding capacity
  • Threaded end is chamfered for ease of starting nut
  • Available in a wide range of diameters and lengths
  • Carbon or stainless steel (Types 303/304; Type 316)
  • Carbon steel anchors are available zinc plated or mechanically galvanized

Applications
The anchor is made from 316 Stainless Steel. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.

Environment
The anchor is designed for use in a submerged/chemicals environment.

Hole Diameter/Bit Diameter
The anchor requires a 5/8" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor
The diameter of the anchor is 5/8".

Length Anchor
The length of the anchor is 6"

Thread Type
The threads on the anchor are national coarse threads that measures 5/8" with 11 threads per inch, commonly referred to as 5/8"-11.

Thread Length
The length of the threads on the anchor is 4-3/8" in length.

Packaging
The anchor is packaged with 20 pieces per box and is packaged with the correct number and diameter of nuts and washers.

Minimum Embedment
The minimum anchor embedment into the concrete is 2-3/4". Therefore, the anchor must be installed so that a minimum of 2-3/4" of the anchor is embedded into the concrete.

Depth of Hole
The depth of the hole that is required for the anchor should be a minimum of 1/2" deeper than the anchor will penetrate the concrete. This will allow space for dust created during the installation process to fall, which will prevent the anchor from bottoming out in the hole before full penetration into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 2-5/8". This will ensure that the minimum embedment of 2-3/4" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 5/8" diameter anchor requires the hole in the fixture to be 11/16".

Wrench Size
The size of the wrench required to turn the nut to set the anchor is 5/16".

Torque Value
To be set properly in the concrete, the anchor must be torqued to between 90 ft./lbs.

Markings
The anchor is stamped with the letter J on the threaded end to allow inspection of the anchor after installation. The letter "J" designates an overall length of the anchor as between 6" up to, but not including 6-1/2" in length.

Products Specifications
Bit Size5/8"
Minimum Embedment2-3/4"
Thread Length4-3/8"
PrimaryConcrete only
EnvironmentSubmerged/Chemicals
Thread Type5/8" - 11
TypeMale
Diameter5/8"
Length6"
Material316 Stainless Steel
Box Qty20
Minimum SpacingSee PDF
Minimum Edge DistanceSee PDF
Maximum Fixture Thickness2-5/8"
Minimum Fixture Hole Diameter (In Place)11/16"
Minimum Fixture Hole Diameter (Hole Spotted)5/8"
Length ID CodeJ
Maximum Torque90 ft./lbs.
Wrench Size For Nut5/16"
Length MeasurementEnd to End
Brand NameSimpson Strong-Tie®
Application Video 

View AllClose

Additional Information

Bit Size:
5/8"
Minimum Embedment:
2-3/4"
Thread Length:
3-3/4"
Primary:
Concrete only
Environment:
Submerged/Chemicals
2000 PSI Concrete - Pull-Out (lbs.) *:
3749
2000 PSI Concrete - Shear (lbs.) *:
6198
Type:
Male
Diameter:
5/8"
Length:
6"
Material:
316 Stainless Steel
Box Qty:
20
Minimum Edge Distance:
3-1/8"
Maximum Fixture Thickness:
2-5/8"
Minimum Fixture Hole Diameter (In Place):
7/8"
Minimum Fixture Hole Diameter (Hole Spotted):
5/8"
Length ID Code:
J
Maximum Torque:
75 - 90 ft./lbs.
Wrench Size For Nut:
15/16"
Length Measurement:
End to End
Brand Name:
CONFAST
View AllClose