CONFAST®

5/8" x 8-1/2" Wedge Anchor Zinc Plated, 20/Box

(No reviews yet) Write a Review
SKU:
WA58812
UPC:
820274002452
Availability:
In Stock, Ships Today!
$51.79

Description

Products Features 
  • ZINC ​PLATED:  Helps ​prevent ​rust ​in ​dry ​environments; dependable ​application ​and ​maintenance 
  • WIDE ​RANGE ​OF ​SIZES:  Ensures ​correct ​fastener ​for ​effective ​results 
  • FOR ​USE ​IN ​CONCRETE ​ONLY:  Provides ​most ​consistent ​holding ​values; ​secure application 
  • PACKAGED ​WITH​ ​NUTS ​AND ​WASHER:  Fast, ​quick, ​complete ​installation 
  • HOLE ​SIZE ​IS ​ANCHOR ​SIZE:  Quick ​and ​easy ​installation; ​simple ​to ​order 
Products specifications 
Bit Size  5/8" 
Box Qty  20 
Minimum Embedment  2-3/4" 
Wrench Size For Nut  15/16" 
Primary  Concrete only 
Minimum Edge Distance  3-1/8" 
Maximum Fixture Thickness  5-1/8" 
Minimum Fixture Hole Diameter (In Place)  7/8" 
Minimum Fixture Hole Diameter (Hole Spotted)  5/8" 
Length ID Code 
Brand Name  CONFAST® 
Maximum Torque  75 - 90 ft./lbs. 
Thread Length  4" 
2000 PSI Concrete - Pull-Out (lbs.) *  3749 
2000 PSI Concrete - Shear (lbs.) *  6198 
Length Measurement  End to End 
Diameter  5/8" 
Length  8-1/2" 
Material  Carbon Steel Zinc Plated 
Environment  Dry 
Type  Male 
* Values shown are average ultimate values and are offered only as a guide and are not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe working load
Application Video 

Installation Video 
Installing a 5/8" x 8-1/2" Wedge Anchor Zinc Plated 
  1. Drill a 5/8" hole into the concrete using a carbide-tipped bit that meets ANSI Standards B212.15. 
  2. Drill the hole a 1/2" deeper than the anchor will penetrate the concrete, making sure the minimum embedment requirements of 2-3/4" is met. 
  3. The hole can be drilled while the fixture is in place. The minimum hole in the fixture for the 5/8" x 8-1/2" Wedge Anchor Zinc Plated is 7/8". 
  4. Clean the hole with a wire brush, vacuum, compressed air, or a blow-out bulb. 
  5. Put the nut and washer on the 5/8" x 8-1/2" Wedge Anchor Zinc Plated, making sure the nut is on the last threads; this will protect the threads from damage when the wedge anchor is hammered into the hole and into the concrete. 
  6. Insert the anchor through the hole in the fixture and into the hole in the base material. 
  7. This should be a very tight fit. Then use a hammer to complete the installation until the nut and washer are tight against the fixture. It is important that the threads go below the surface of either the base material or the fixture. 
  8. Turn the nut clockwise on the anchor until finger tight. 
  9. Using a 15/16" wrench, turn the nut 3 to 4 times until snug or until the proper torque value of 75 - 90 ft./lbs. is reached. 
  10. Always use proper personal protective equipment per manufacturer's and OSHA instructions. 

View AllClose

Additional Information

Bit Size:
5/8"
Minimum Embedment:
2-3/4"
Thread Length:
4"
Primary:
Concrete only
Environment:
Dry
2000 PSI Concrete - Pull-Out (lbs.) *:
3749
2000 PSI Concrete - Shear (lbs.) *:
6198
Type:
Male
Diameter:
5/8"
Length:
8-1/2"
Material:
Carbon Steel Zinc Plated
Box Qty:
20
Minimum Edge Distance:
3-1/8"
Maximum Fixture Thickness:
5-1/8"
Minimum Fixture Hole Diameter (In Place):
7/8"
Minimum Fixture Hole Diameter (Hole Spotted):
5/8"
Length ID Code:
O
Maximum Torque:
75 - 90 ft./lbs.
Wrench Size For Nut:
15/16"
Length Measurement:
End to End
Brand Name:
CONFAST
View AllClose