Simpson Strong-Tie

3/8" x 1-3/4" Simpson Strong-Tie Titen HD Screw Anchor Zinc Plated, 50/Box

(No reviews yet) Write a Review

SKU:: CSH38134;SC
UPC:: 707392594703
MPN:: THD37134H
Availability:: In Stock, Ships Today!

$104.23

Current Stock:

Quantity:

Description
Additional Information

Description

Products Features

COMPLETE LINE: Ensures correct product can be located and purchased for any job
ALL LENGTHS ARE AVAILABLE: Using the correct length screw ensures quality, secure fastening
SPECIAL THREADS: Decreases installation torque allowing screw to be installed faster and easier
TWO DIAMETERS: 3/16" and 1/4" Choice allows for wider variety of fastening applications depending on the hole in the fixture being attached
BIT INCLUDED IN EACH BOX: Using the correct bit will give you better-holding values

Products specifications

Bit Size	3/8"
Minimum Embedment	See PDF
Box Qty	50
Thread Type	Undercut Design
Type	Male
Diameter	3/8"
Length	1-3/4"
Material	Carbon Steel
Environment	Dry
Minimum Spacing	See PDF
Minimum Edge Distance	See PDF
Maximum Fixture Thickness	See PDF
Minimum Fixture Hole Diameter (In Place)	1/2"
Minimum Fixture Hole Diameter (Hole Spotted)	1/2"
Maximum Torque	See PDF
Wrench Size For Nut	9/16"
Length Measurement	Underneath head
Brand Name	Simpson Strong-Tie

* Values shown are average ultimate values and are offered only as a guide and are not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe working load

Applications
The anchor is made from Carbon Steel, and is zinc plate. This anchor is designed for use in

Environment
The anchor is designed for use in a dry environment.

Head Style
The anchor is a Hex Washer Serrated head and is designed to allow the head to sit on top of the surface of the item being attached.

Hole Diameter/Bit Diameter
The anchor requires a 3/8" hole to be drilled in the base material (). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Driver Required
A 9/16" is required for driving the anchor into the base material.

Diameter of Anchor
The diameter of the anchor is 3/8".

Length Anchor
The length of the anchor is 1-3/4"

Packaging
The anchor is packaged with 50 pieces per box .

Depth of Hole
The depth of the hole that is required for the anchor should be a minimum of 1/2" deeper than the anchor will penetrate the concrete. This will allow space for dust created during the installation process to fall, which will prevent the anchor from bottoming out in the hole before full penetration into the concrete.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 3/8" diameter anchor requires the hole in the fixture to be 1/2".

Wrench Size
The size of the wrench required to turn the nut to set the anchor is 9/16".

Torque Value
To be set properly in the concrete, the anchor must be torqued to between See PDF

Installing a 3/8" x 1-3/4" Simpson Strong-Tie Titen HD Screw Anchor Zinc Plated (ea) THD37134H

Drill a 3/8" hole into the concrete using a carbide-tipped bit that meets ANSI Standards B212.15.
Drill the hole a 1/2" deeper than the anchor will penetrate the concrete, making sure the minimum embedment requirements of 1" is met.
Clean the hole with a wire brush, vacuum, compressed air, or a blow-out bulb.
Insert the point of the 3/8" x 1-3/4" Simpson Strong-Tie Titen HD Screw Anchor Zinc Plated (ea) THD37134H into the hole. Make sure that the screw being installed will penetrate the base material a minimum of 1" but no deeper than 1-3/4".
Turn the screw clockwise, applying slight pressure until the head of the screw is snug against the material being fastened.
Always use proper personal protective equipment per manufacturer's and OSHA instructions.

View AllClose

Additional Information

Bit Size:	3/8"
Minimum Embedment:	1-1/2"
Environment:	Dry
Material:	Carbon Steel Zinc Plated
Thread Type:	Undercut Design
2000 PSI Concrete - Pull-Out (lbs.) *:	1336
2000 PSI Concrete - Shear (lbs.) *:	2108
Type:	Male
Diameter:	3/8"
Length:	1-3/4"
Box Qty:	50
Minimum Spacing:	6"
Minimum Edge Distance:	3"
Maximum Fixture Thickness:	1/4"
Minimum Fixture Hole Diameter (In Place):	7/16"
Minimum Fixture Hole Diameter (Hole Spotted):	7/16"
Length ID Code:	A
Wrench Size For Nut:	9/16"
Head Type:	Hex Washer Serrated
Length Measurement:	Underneath head
Driver Size:	9/16"
Brand Name:	Simpson Strong-Tie